View LQ064V3DG01_456536.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PRODUCT SPECIFICATIONS Mobile Liquid Crystal Displays Group
www..com
LQ064V3DG01
TFT-LCD Module
Spec. Issue Date: May 16, 2005 No: LAI-04032C
www..com
www..com
LA1-04032C-1 NOTICE
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. any purpose, in whole or in part, without the express written permission of SHARP. also required before any use of this publication may be made by a third party. The application circuit examples in this publication are provided to explain the representative applications of SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be executed. SHARP takes no responsibility for any problems related to any industrial property right or a third party resulting from the use of SHARP's devices, except for those resulting directly from device manufacturing processes. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. obtain the latest device specification sheets before using any SHARP's device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice. Observe the following points when using any device in this publication. SHARP takes no responsibility for damage caused by improper use of the devices. The devices in this publication are designed for general electronic equipment use. The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for equipment such as: Transportation control and safety equipment(i.e.,aircraft, trains, automobiles, etc.)
Traffic signals Gas leakage sensor breakers Alarm equipment Various safety devices etc.
Under the copyright laws,
www..com
no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for Express written permission is
Contact SHARP in order to
SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as: Military and space applications Medical equipment for life support Contact a SHARP representative, in advance, when intending to use SHARP's devices for any "specific" applications other than those recommended by SHARP. Contact and consult with a SHARP representative if there are any questions about the contents of this publication. Nuclear power control equipment
LA1-04032C-2
1 2
Applicable TFT-LCD module
This specification applies to the color TFT-LCD module, LQ064V3DG01.
www..com
Overview
This module is a color active matrix transmissive LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, control circuits and power supply circuitry and a backlight unit. Graphics and texts can be displayed on a 640 x RGB x 480 dots panel with 262,144 colors by feeding 18 bit data signal (6bit/each of R,G,B), 4(four) timing signals, +3.3V or +5V DC power supply for TFT-LCD and AC power supply for backlight. (Note: Backlight-driving DC/AC inverter is not built in this module.) Fine images with stripe aligned 307,200 pixels on 6.4 inch diagonal screen Color display capability of 262,144 colors with 18 bit data signal(6 bits for each RGB) Adapting a wide viewing angle technology [best viewing angle: 6 o'clock direction] High contrast, thanks to active matrix drive system AG(Anti Glare) polarizing filter Light and slim compact module achieved by COG assemble technology 12 o'clock direction is also available by the function to flip the screen horizontally or vertically) Natural coloring reproducibility by employing normally-white-mode, which has good nature in coloring Image inversion both horizontally and vertically
3
Mechanical Specifications
items Display size (Diagonal) Active display area Pixel format specifications 16.32 (6.4") 130.56 (H) x 97.92 (V) 640(H) x RGB x 480(V) (1 pixel=R+G+B dots) Pixel pitch Pixel configuration LCD mode Dimension * Mass Fig.1 shows dimensions of the module. 0.204 (H) x 0.204(V) R,G,B vertical stripe Normally white/Twisted Nematic 161.3 (W) x 117 (H) x 12(D) 280 max unit cm mm dot mm mm g
*. Protrusion such as backlight harness and positioning boss are not included.
www..com
LA1-04032C-4 [Note 2]
www..com
(R/L=High, U/D=High)
(R/L=Low, U/D=High)
(R/L=High, U/D=Low) 4.2 CN2 Pin no. 1 2 3 4 VLOW Symbol VHIGH VHIGH Backlight section
(R/L=Low, U/D=Low) Employed connector: BHR-0 VS-1 (JST) Adapted connector: SM04 (4.0) B-BHS-1 (JST) Function
Power supply for lamp (High voltage side) Power supply for lamp (High voltage side) This is electrically opened. Power supply for lamp (Low voltage side) and terminal should be in a same phase.
The input voltage wave forms to terminal
It has the possibility to discharge abnormally between the terminals in case of input in a reversed phase.
5
Absolute Maximum Ratings
Parameter Input voltage Supply voltage Storage temperature Operating temperature (Panel surface) Symbol Condition VI Vcc Tstg Topp Ta=25C Ta=25C Ratings -0.3 ~ +6 0 ~ +6 - 30 ~ +80 -10 ~ +70 Unit V V C C [Note 2] Remark [Note 1] -
[Note 1] CK, R0 ~ R5, G0 ~ G5, B0 ~ B5, Hsync, Vsync, ENAB, R/L and U/D [Note 2] Humidity: Less than 95%RH at Ta 40C and Maximum wet-bulb temperature must not exceed 39C at Ta>40C, with no condensation.
LA1-04032C-5
6
Electrical characteristics
6.1 TFT-LCD Panel driving section Parameter Symbol Vcc Vcc Icc Icc Ta 25 Min +3.0 +4.5 - 0.3 2.3 |IOL2| [Note5] |IOL | [Note6] |IOL4| [Note7] |IOH1| Typ +3.3 +5.0 290 200 Max +3.6 +5.5 580 400 100 0.9 5.5 1.0 1.0 6.0 7.0 120 180 6.0 6.0 1.0 1.0 6.0 7.0 40 80 6.0 6.0
2.8V
Unit V V mA mA mV p-p V V A A A A A A A A A A A A A A A A
2.8V
www..com Remarks
Supply voltage
[Note1] [Note2] Vcc=3.3V [Note2] Vcc=5.0V Vcc=5V/3.3V [Note3]
Vcc=3.3V VI=0V Vcc=5.0V VI=0V Vcc=3.3V VI=0V Vcc=5.0V VI=0V Vcc=3.3V VI=0V Vcc=5.0V VI=0V Vcc=3.3V VI=0V Vcc=5.0V VI=0V
Vcc=3.3V VI=3.3V Vcc=5.0V VI=5.0V Vcc=3.3V VI=3.3V Vcc=5.0V VI=5.0V Vcc=3.3V VI=3.3V Vcc=5.0V VI=5.0V Vcc=3.3V VI=3.3V Vcc=5.0V VI=5.0V
VCC data
Current dissipation
Allowed input ripple voltage Input voltage ("Low" state) Input voltage ("High" state) Input leakage current (low)
VRF VIL VIH
IOL1
[Note4]
Input leakage current (High)
[Note ] |IOH2| [Note ] |IOH3| [Note ] |IOH3|
[Note7] [Note1] Vcc turn-on/off conditions VCC 0 < t1 15ms data 0 < t2 20ms 0 < t3 1s 1s < t4 Vcc-dip conditions 1) At 2.7V Vcc < 3.0V td 10ms 2) At Vcc < 2.7V Vcc dip conditions should also follow the Vcc turn-on/off conditions [Note2] Current dissipation (Typ.):
0.3V t3
0.3V time
VCC 3.0V
t4
t1
t2
2.
V
t
When Monochrome 16 level-gray-bar pattern is displayed (Figure below, Refer Page 10 for details of RGB)
Current dissipation (Max.): When GS3 and GS10 gray bar are displayed alternately. [Note3] CK, R0~R5, G0~G5, B0~B5, Hsync, Vsync, ENAB, R/L and U/D [Note4] R0~R5, G0~G5, B0~B5, Hsync, and Vsync [Note5] ENAB [Note6] R/L and U/D [Note7] CK
LA1-04032C-6 Backlight driving Section Parameter Symbol Lamp voltage VL Lamp current IL Lamp frequency fL Vs 6.2 Min. 330 9.0 35 Typ. 370 10.0 Max. 410 11.0 80 660 530 960 770 Unit V rms mA rms 5mArms 2[Note6-1] KHz V rms Ta=25C Remarks IL=5 www..com 2mA rms
Recommend Ta=-10C [Note6-2] Kick-off voltage Ta=25C [Note6-2] [Note6-1] Ta=-10C [Note6-3] Ta=25C [Note6-3] [Note6-4] (Inverter: HARISON TOSHIBA LIGHTING CORPORATION Type HIU-359A-S2(18pF) is used at drive frequency f=50kHz) Caution: Use Inverter providing symmetrical sine-wave in positive/negative polarity with no spike. [Note6-1] Connect Module's metal shield case to GND of inverter circuit. There are two lamps in back light. A piece of lamp current is 5mArms. Lamp current is measured with current meter for high frequency as shown below.
[Note6-2] The voltage at the output of inverter circuitry. The open output voltage of the inverter shall be maintained for more than 1sec; otherwise the lamp may not be turned on. The input voltage wave forms to terminal and terminal should be in a same phase. It has the possibility to discharge abnormally between the terminals in case of input of a reversed phase. For the sake of the safety, please so design the inverter as to prevent abnormal discharge when one of the two lamps is broken or reaches the end of life. [Note6-3] The voltage at the output of transformer built in inverter circuitry [Note6-4] The data for lamp is for your reference, because lamp is consumable component. a) Lamp life time is defined by either 1or 2 below. (Continuous turning on at Ta=25 , IL=5 2mA rms) When a brightness of lamp surface became 50% of the initial value under the standar condition When a kick-off voltage in Ta= -10 exceeded maximum value (960 Vrms) at the output of inverter circuitry ) In case of operating under lower temp. environment, the lamp exhaustion is accelerated and the brightness becomes lower. (Continuous operating for around 1 month under lower temp. condition may reduce the brightness to half of the original brightness.) In case of such usage under lower temp. environment, periodical lampexchange is recommended
www..com
www..com
LA1-04032C-9
8
Input Signals, Basic Display Colors and Gray Scale of Each Color
www..com
Colors & Gray scale Black Blue Green Cyan Red Magenta Yellow White Black Darker
Gray Scale
Data signal R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5
0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0
Basic Color
GS0 GS1 GS2
Gray Scale of Red
Brighter Red Black Darker
Gray Scale of Green
GS61 GS62 GS63 GS0 GS1 GS2
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Brighter Green Black Darker
Gray Scale of Blue
GS61 GS62 GS63 GS0 GS1 GS2
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
GS61 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 GS62 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 GS63 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 Blue 0: Low level voltage, 1: High level voltage Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen.
Brighter
1 1 1
1 1 1
1 1 1
LA1-04032C-10
9
Optical Specification
Parameter Symbol 21, 22 11 12 CR max Tr Td x y Luminance Y
IL=10mA
www..com
Ta=25C, Vcc=+3.3V Condition CR5 Min. 60 35 55 Best viewing angle Response time Rise Fall Chromaticity of white = 0 0.263 0.279 260 8 21 0.313 0.329 350 20 40 0.363 0.379 ms ms [Note9-4] [Note9-3] 250 Typ. 70 40 70 350 Max. Unit (Deg.) (Deg.) (Deg.) [Note9-2] Remark [Note9-1,4] Viewing angle Range Horizontal Vertical Contrast ratio
Lamp test in the module is made with the inverter type HIU-359A-S2(18pF) at 50kHz The optical specifications are measured 30 minute after turning lamp on and in a dark room or equivalent condition, according to the method shown in Fig.9-1, 2 below.
0mm~Focal distance Sensor (EZ-CONTRAST) 400mm Sensor (BM-5A/BM-7/SR-1)
Field=2
Center of LCD screen TFT LCD Module
Center of LCD screen TFT LCD Module
Fig.9-1 Measuring setup for Viewing angle and Contrast ratio
(BM-7 is used for contrast.)
Fig.9-2 Measuring setup for Luminance, Chromaticity and Response time
(BM-7 is used for Luminance, SR-1 is for response)
LA1-04032C-11 [Note9-1] Definitions of viewing angle range:
www..com
[Note9-2] Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR)
Luminance (brightness) with all pixels white Luminance (brightness) with all pixels black
[Note9-3] Definition of response time: The response time is defined as the following figure and shall be measured by switching the input signal between "black" and "white" alternatively.
[Note9-4] This parameter should be measured at the center of the screen and 30 minutes after turn-on. Inverter frequency: 50 kHz The characteristics are measured when the driver circuit is not powered.
LA1-04032C-12
10 11
Display Qualities
Please refer to the Outgoing Inspection Standard.
www..com
Handling Instruction
11.1 Assembling the module 1) In this module, the contact of the front shield case and the back is not always contact electrically each other. The front shield case and the back touches at the point "A" hole perfectly, when this module is mounted to the unit of customer. Therefore, please fix the mounting hole in the same plane in the case of the module installation, so that stress such as bow and crook may not be added to the module. To ensure the electric contact of the front shield case and the back, please fasten the mounting hole "A" of figure.1 surely, when you mount this module to the customer's set. 2) Connection/disconnection of the module's input connector shall be made while power is off. 3) Make sure to connect module's metal shield case to GND of inverter circuit. If its connection is not made perfectly, some of the following problems may occur. a) Increase of noise caused by backlight b) Unstable output from inverter circuit c) Possibly over-heat in some section 11.2 Instruction for assembling Since the front polarizer is easily damaged, pay attention to avoid rubbing with something hard or sharp. A protective film "Laminator" is attached on the module screen to avoid scratch and/or dust. You are recommended remove the "Laminator" just before you embed the module into your products, paying attention to avoid electrostatic damage as followings. A) Work Environment Since removing laminator may causes electrostatic charge that tends to attract dust, the following work environment would be desired. a) Floor: Conductive treatment having 1M resistance onto floor's tile b) The room free from dust coming from outdoor environment, and put an adhesive mat at entrances c) Humidity from 50% to 70% and temperature from 15C to 27C are desirable. d) Worker should ware conductive shoes, conductive fatigue, conductive glove and earth wrist band. B)Instruction for working
a) Wind direction of an electrostatic discharging blower should slightly downward to properly blow the module. The distance between the blower and the module should be Also, pay attention to the direction of the module. [See the above] less than 20cm.
LA1-04032C-13 b) To prevent polarizer from scratching, adhesive tape (cellophane tape) should be stuck at www..com the part of laminator sheet, which is closed to blower. [See the above] c) Pull slowly adhesive tape to peel the laminator off, with spending more than 5 second. d) The module without laminator should be moved to the next process to prevent dust. e) How to eliminate dust on polarizer. Blow dust away by N2 blower having measures of electrostatics Since the front polarizer is easily damaged, wiping dust off is not adequate. If the polarizer is soiled, it is suggested to peel dust off by using adhesive surface of adhesive tape. When the metal section [shield case or shield back case] is soiled, wipe it off with dry and soft cloth. If not so easy, breathe upon it then wipe off. If the water droplet or fat is left for long term, it may cause stain or tarnish, it should be wipe off immediately. Since TFT-LCD panel is made of glass substrate, dropping the panel or banging it against hard objects may cause cracking or fragmentation. Since CMOS LSIs are incorporated in this module, please pay special care to electrostatic while handling it, and earth human body. 11.3 Caution in product design The notes and cautions below should be followed when product is designed with this module. The module should be protected with cover to prevent salt content and/or water droplet. Take enough shielding countermeasure not to interfere to peripheral electronic device. 11.4 Others The LCD has the nature that its performance is degradation by ultra-violet light. Don't leave the LCD module in direct sunlight or strong ultra violet ray. If stored at the temperatures lower than the rated storage temperature, the LC may freeze and it may cause LCD panel damage. If storage temperature exceeds the specified rating, the molecular orientation of the LC may change to that of a liquid, and they may not revert to their original state. Store the module in normal room temperature. The inductive loss caused by routing of lamp lead wire, which is closed to conductive section, may require the kick-off voltage greater than specified kick-off voltage. The liquid crystal may leak out when the LCD is broken. If the liquid crystal drip into the eyes or mouth washes it out immediately. The caution to other ordinal electronic component should be followed also.
12
LA1-04032C-14 www..com
Packing Form
12.1 Fig.3 shows packaging form. 12.2 Carton stock conditions a) Maximum number of Carton being stuck: 8 b) Maximum number of product contained: 20 Unit c) Carton size: 495mm (W) x 329mm (H) x 218mm (D) d) Total mass (for 20Unit): Approximately kg e) Carton stock environment: ) Temperature: 0 ~ 40C 2) Humidity: Up to 60%RH 3) Ambiance: No gases bite into electronic components and wiring materials 4) Period: Approximately 3month 5) Unpacking: To prevent LCD module from damaging by ESD, unpack the module with effective measure after controlling humidity 50%RH or more.
13
Marking of product name
13.1 Serial No. indication Serial No. is indicated by labeling. The location is given in Fig.1 Outline dimension. Indicated contents:
LQ064V3DG01
XXXXXXXXX
Model name Serial No. Serial No. contents 1st digit: last digit of produced year (ex. 2004 "4") 2nd digit: Produced month 1, 2, 3 ~ 9, X, Y, Z 3rd ~ 8th digit: Sequential number 000001 ~ 9th digit: Interoffice control code
14
Miscellaneous a) Variable resister has been set optimally before shipment, so do not change any adjusted value. If adjusted value is changed, the specification may be not satisfied. b) Don't disassemble this module, it may cause malfunction. c) Image retention may occur when the fixed image is display for long time.
LA1-04032C-15
15
No. 1 2 3 4 5 6 7
Reliability Test Items
www..com
Note: The condition of temperature is the operation temperature given in Absolute maximum rating. Test parameter High temperature storage test Low temperature storage test High temperature & high humidity operation test High temperature operation test Low temperature operation test Strength against ESD Shock test (non- operating) Conditions Leaves the module at Ta=80C for 240h Leaves the module at Ta=-30C for 240h Operates the module at Ta=40C; 90~95%RH for 240h (No condensation) Operates the module with +70C at panel surface for 240h Operates the module at Ta=-10C for 240h 200V 200pF [0 ] one time for each terminal Max. acceleration : 490m/s2 Pulse width : 11ms, half sine wave Direction : X,Y,Z once for each direction. 8 Vibration test (non- operating)
Frequency : 10 : 58 57Hz/Vibration width (one side):0.075mm 500Hz/Gravity:9.8m/s2
Sweep time : 11 minutes Test period : 3 hours
(1 hour for each direction of X,Y,Z)
9
Thermal shock test
-30C ~ +80C /50 cycle [0.5h] [0.5h]
[Result Evaluation Criteria] Under the display quality test conditions with normal operation state, these shall be no change which may affect practical display function. [Note] The directions of X, Y, Z are defined as below:
Z
X
Y
www..com
www..com
www..com
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
www..com
Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP's product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible, for any incidental or consequential economic or property damage.
NORTH AMERICA
EUROPE
JAPAN
SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 Fax: (1) 360-834-8903 Fast Info: (1) 800-833-9437 www.sharpsma.com
SHARP Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com
SINGAPORE
SHARP Corporation Electronic Components & Devices 22-22 Nagaike-cho, Abeno-Ku Osaka 545-8522, Japan Phone: (81) 6-6621-1221 Fax: (81) 6117-725300/6117-725301 www.sharp-world.com
TAIWAN
KOREA
SHARP Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 Fax: (886) 2-2577-7326/2-2577-7328
SHARP Electronics (Singapore) PTE., Ltd. 438A, Alexandra Road, #05-01/02 Alexandra Technopark, Singapore 119967 Phone: (65) 271-3566 Fax: (65) 271-3855
SHARP Electronic Components (Korea) Corporation RM 501 Geosung B/D, 541 Dohwa-dong, Mapo-ku Seoul 121-701, Korea Phone: (82) 2-711-5813 ~ 8 Fax: (82) 2-711-5819
CHINA
HONG KONG
SHARP Microelectronics of China (Shanghai) Co., Ltd. 28 Xin Jin Qiao Road King Tower 16F Pudong Shanghai, 201206 P.R. China Phone: (86) 21-5854-7710/21-5834-6056 Fax: (86) 21-5854-4340/21-5834-6057 Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp
SHARP-ROXY (Hong Kong) Ltd. 3rd Business Division, 17/F, Admiralty Centre, Tower 1 18 Harcourt Road, Hong Kong Phone: (852) 28229311 Fax: (852) 28660779 www.sharp.com.hk Shenzhen Representative Office: Room 13B1, Tower C, Electronics Science & Technology Building Shen Nan Zhong Road Shenzhen, P.R. China Phone: (86) 755-3273731 Fax: (86) 755-3273735

▲Up To Search▲

Price & Availability of LQ064V3DG01

	To Download LQ064V3DG01 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .